manualshive.com logo in svg

Altuscn KM0032, User Manual, Page: 24 / 155

Share
Download
Altuscn KM0032 User Manual Download Page 24

KM0032 / KM0532 / KM0932 User Manual

12

Before you Begin

Stacking and Rack Mounting

The KM0032 / KM0532 / KM0932 can be stacked on the desktop or rack 
mounted in a variety of ways. The following sections take you through the 
procedures for each method.

Stacking

The KM0032 / KM0532 / KM0932 can be placed on any appropriate level 
surface that can safely support its weight plus the weight of its attached cables. 
To place the switch, or to stack units if you are daisy chaining them, remove 
the backing material from the bottom of the rubber feet that came with this 
package, and stick them onto the switch’s bottom panel at the corners, as 
shown in the diagram, below:

Note:

To ensure adequate ventilation, allow at least 5.1 cm on each side, and 
12.7cm at the back for power cord and cable clearance.

1. Important safety information regarding the placement of this 

device is provided on page 121. Please review it before 
proceeding.

2. Make sure that power to all the devices you will be connecting 

up has been turned off. You must unplug the power cords of any 
computers that have the Keyboard Power On function.

Summary of Contents for KM0032




























































































































































Reviews:

No comments