manualshive.com logo in svg

Altuscn KM0032, User Manual, Page: 138 / 155

Share
Download
Altuscn KM0032 User Manual Download Page 138

KM0032 / KM0532 / KM0932 User Manual

126

IP Address Determination

If you are an administrator logging in for the first time, you need to access the 
KM0032 / KM0532 / KM0932 in order to give it an IP address that users can 
connect to. There are three methods to choose from. In each case, your 
computer must be on the same network segment as the KM0032 / KM0532 / 
KM0932. After you have connected and logged in you can give the KM0032 / 
KM0532 / KM0932 its fixed network address. (See

Network

, page 44.)

The Local Console

The easiest way to assign an IP address is from the local console. Refer to 

First 

Time Setup

, page 27, for details on the procedure involved.

IP Installer

For computers running Windows, an IP address can be assigned with the 

IP 

Installer

 utility. The utility can be obtained from the 

Download

 area of our web 

site. Look under 

Driver/SW

, and the model of your switch. After downloading 

the utility to your computer, do the following:

1. Unzip the contents of 

IPInstaller.zip

 to a directory on your hard drive.

2. Go to the directory that you unzipped the IPInstaller program to and run 

IPInstaller.exe

. A dialog box similar to the one below appears:

Summary of Contents for KM0032




























































































































































Reviews:

No comments