manualshive.com logo in svg

Altuscn KM0032, User Manual, Page: 19 / 155

Share
Download
Altuscn KM0032 User Manual Download Page 19

 Chapter 1. Introduction

7

4

LAN  LED

Š

The LED lights ORANGE to indicate 10 Mbps data 
transmission speed.

Š

The LED lights GREEN to indicate 100 Mbps data 
transmission speed.

Š

The LED flashes when data is being transmitted

5

Reset Switch

Pressing in this button performs a system reset. When the 
system is reset, the switch beeps, and then the KVM port 
LEDs flash in succession until the reset is completed. After 
the reset is completed you can login again.

Note

: This switch is recessed and must be pushed with a 

thin object.

6

Cover Latch

7

Firmware 
Upgrade 
Recovery Switch

During normal operation and while performing a firmware 
upgrade, this switch should be in the NORMAL position. If a 
firmware upgrade operation does not complete successfully, 
this switch is used to perform a firmware upgrade recovery 
(see 

Firmware Upgrade Recovery

, page 104, for details).

8

Console (User) 
Port

This console port is provided on the front panel for easy 
administrative access

No.

Component

Description

Summary of Contents for KM0032




























































































































































Reviews:

No comments