manualshive.com logo in svg

Altera Stratix III, Using Manual, Page: 50 / 59

Share
Download
Altera Stratix III Using Manual Download Page 50

Page 50

Example Project Walkthrough

AN 436: Using DDR3 SDRAM in Stratix III and Stratix IV Devices

© November 2008

Altera Corporation

The report indicates that 

clk6

 of the PLL is clocking the address and command 

registers. Go to the PLL megafunction and change the phase setting of 

clk6

. For this 

design, the initial phase setting of 

clk6

 is set to 315°, resulting in the address and 

command being launched too early, which causes a hold time violation. To remedy 
this violation, delay the launch of the address and command by delaying 

clk6

, by 

increasing the phase setting. The negative hold margin reported is –45 ps. Therefore, 
delay 

clk6

 by an amount larger than that. Using the frequency of 

clk6

, translate the 

amount of time delay to degrees in the PLL setting. For this example, 

clk6

 is 

200 MHz which 45 ps translates to 3°. To ensure positive margin for hold, delay 

clk6

 

by more than 3°, which means the new phase setting for 

clk6

 is larger than 318°. For 

this example, set the new phase setting for 

clk6

 to 330° so there is sufficient hold 

time. Alternatively, you can select a phase that balances setup and hold times.

After modifying the 

clk6

 phase setting, recompile the design for the new PLL setting 

to take effect. Run the report timing script again.

Figure 20.

Report on the Path that Violates Hold Time

Summary of Contents for Stratix III




























































Reviews:

No comments