Altera Stratix III Using Manual Download

Page: 41 / 59

Example Project Walkthrough

Page 41

Altera Corporation

AN 436: Using DDR3 SDRAM in Stratix III and Stratix IV Devices

3. Place

pins within their respective DQ group.

4. Place address and control command pins on any spare I/O pins ideally within the

same bank or side of the device as the

mem_clk

pins.

5. Ensure you place

mem_clk

pins on differential I/O pairs for the

CK/CK#

pin pair.

To identify differential I/O pairs, right-click in Pin Planner and select

Show

Differential Pin Pair Connections

. Pin pairs show a red line between each pin

pair.

You must place

mem_clk[0]

and

mem_clk_n[0]

on a

DIFFIO_RX

pair.

6. Place the

clock_source

pin on a dedicated PLL clock input pin with a direct

connection to the SDRAM controller PLL and DLL pair—usually on the same side
of the device as your memory interface. This recommendation reduces PLL jitter,
saves a global clock resource, and eases timing and fitter effort.

7. Place the

global_reset_n

pin (like any high fan-out signal) on a dedicated

clock pin.

For more information on how to use the Quartus II Pin Planner, refer to the

I/O

Management

chapter in volume 2 of the

Quartus II Handbook

Figure 13.

Quartus II Pin Planner, Show DQ/DQS Pins, In x8/x9 Mode

Summary of Contents for Stratix III




























































Search results

Summary of Contents for Stratix III

Reviews:

Related manuals for Stratix III

Brands by name

Popular brands

Altera Stratix III, Using Manual

Search results

Summary of Contents for Stratix III

Reviews:

Related manuals for Stratix III

Brands by name

Popular brands