39
-EN
01GB06IVA106E.fm
ALPINE IVA-D106E 68-12118Z27-A (EN)
X-OVER Adjustment
Setting item : X-OVER
1
Touch
[
]
or
[
]
of X-OVER to select L/R or L+R.
2
Touch
[
]
of X-OVER.
3
Touch
[
]
of the speaker (LOW/MID/HIGH) to be
adjusted.
The screen changes to the X-OVER screen to be adjusted.
4
Adjust the crossover to your preference.
2.2ch (3WAY) System
2.2ch (3WAY) System / L+R
Setting contents:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAY) System / L/R
Setting contents:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
4.2ch (FRONT/REAR/SUBW.) System
4.2ch (FRONT/REAR/SUBW.) System / L+R
Setting contents:
LOW (SUBW) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / L/R
Setting contents:
LOW (SUBW)-L / LOW (SUBW)-R / MID (REAR)-L /
MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R
Selecting the Cut-Off Frequency
Touch
[
]
or
[
]
of FREQ., then select the cut-off
frequency (crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
2.2ch (3WAY) System
Setting contents:
LOW / MID-L 20 Hz~200 Hz
MID-H
20 Hz~20 kHz
HIGH
(1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)
*
2
4.2ch (FRONT/REAR/SUBW.) System
Setting contents:
20 Hz~200 Hz
*
1
When MAKER is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 41).
*
2
When USER is selected, refer to “Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 41).
Adjusting the Level
Touch
[
]
or
[
]
of LEVEL to adjust the level.
Adjustable output level: -12 to 0 dB.
Adjusting the Slope
Touch
[
]
or
[
]
of SLOPE to adjust the slope.
Adjustable slope: FLAT
*
,
-
6 dB/oct.,
-
12 dB/oct.,
-
18 dB/oct.,
-
24 dB/oct.
* FLAT can be set for the HIGH slope only when USER is selected in
“Setting the Response Slope for the High Range Speaker
(TW Setup)” (page 41). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
•
Check the playback frequencies of the connected speakers before
adjusting.
•
While adjusting the X-Over, you should consider the frequency
response of the connected speakers.
•
About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system
You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
switch on the PXA-H100. For details, refer to the Owner’s Manual of
PXA-H100.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 41).
1
Touch
[
]
of T.CORR.
The T.CORR adjustment screen appears.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Touch
[
]
or
[
]
of the desired speaker to adjust
the distance.
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 42.
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
L/R:
Different adjustment values can be set for the left
and right channels.
L+R:
Sets the same adjustment values for the left and
right channels.
FRONT L(Mid-L) / FRONT R(Mid-R) / REAR L(High-L) /
REAR R(High-R) / SUBW. L / SUBW. R
FRONT L / FRONT R / REAR L / REAR R / SUBW. L / SUBW. R
01GB00IVAD106E.book Page 39 Tuesday, January 15, 2008 2:48 PM
