Allied Stingray Technical Manual Download Page 97

Page: 97 / 357

Camera interfaces

STINGRAY Technical Manual

V4.4.2

Board level camera: I/O pin assignment

The following diagram shows the 13-pole I/O pin connector of a board level
camera:

Figure 46: Board level camera: I/O pin assignment

sensor board

  1 = GND (for RS232, Ext PWR)
  2 = Ext PWR input
        (PWR output on demand)
  3 = Output 4
  4 = Input 1
  5 = Output 3
  6 = Output 1

FFC45 cable length:
-----------------------------
FFC45 L = 56 mm K7500307
FFC45 L = 110 mm K7500318

FFC45 cable

2x HOLE

2.9mm PTH

2.3 mm

PTH

2.3 mm

PTH

IO-AD-Board

processor board

interface board

2x IEEE 1394b

spacer M2x10 (4x)

  7 = GND (for Inputs)
  8 = RxD  9 = TxD
10 = Power Input
        (for Output ports)
11 = Input 2
12 = Output 2
13 = Cable Shield

13-pole I/O connector:

[Molex 1.25mm Pitch PicoBlade Wire-to-Board Header (53047-1310)]

----------------------------------------------------------------------------------

13-pole connector

9.1

front flange with C-Mount adapter

6.5

Summary of Contents for Stingray






































































































































































































































































































































































Search results

Summary of Contents for Stingray

Reviews:

Brands by name

Popular brands

Allied Stingray, Technical Manual

Search results

Summary of Contents for Stingray

Reviews:

Brands by name

Popular brands