Allied Stingray Technical Manual Download Page 268

Page: 268 / 357

Configuration of the camera

STINGRAY Technical Manual

V4.4.2

269

420h + 000002h x 4 = 428h

The entry with key D1 in the root directory (424h in this case) provides the
offset for the unit directory as follows:

424h + 000004 x 4 = 434h

The entry with key D4 in the unit directory (440h in this case) provides the
offset for unit dependent info:

440h + 0000xx * 4 = 444h

To compute the effective start address of the node unique ID leaf

currAddr

= node unique ID leaf address

destAddr

= address of directory entry

addrOffset

= value of directory entry

destAddr

= cu (4 x addrOffset)

= 420h + (4 x 000002h)

= 428h

Table 111: Computing effective start address

Offset

0-7

8-15

16-23

24-31

428h

....

CRC

Node unique ID leaf

42Ch

….

Node_Vendor_Id

Chip_id_hi

430h

Serial number

Table 112: Configuration ROM

Offset

0-7

8-15

16-23

24-31

Unit directory

434h

438h

43Ch

440h

Table 113: Configuration ROM

Summary of Contents for Stingray






































































































































































































































































































































































Search results

Summary of Contents for Stingray

Reviews:

Brands by name

Popular brands

Allied Stingray, Technical Manual

Search results

Summary of Contents for Stingray

Reviews:

Brands by name

Popular brands