manualshive.com logo in svg

Allied Stingray, Technical Manual

Share
Download
Allied Stingray Technical Manual Download Page 111

Camera interfaces

STINGRAY Technical Manual

 

V4.4.2

111

PWM: minimal and maximal periods and frequencies

In the following formulas you find the minimal/maximal periods and frequen-
cies for the pulse-width modulation (PWM).

 Figure 51: PulseWidth and Period definition

Note

Note the following conditions:

•

PulseWidth 

 Period

•

Period 

 MinPeriod

 Formula 1: Minimal/maximal period and frequency

PulseWidth

Period

period

min

3µs

=

  

 

frequency

max

1

period

min

----------------------

1

3µs

--------

333.33kHz

=

=

=

frequency

min

1

2

16

6

–

10 s

-------------------------

15.26Hz

=

=

  

 

period

max

1

frequency

min

-------------------------------

2

16

µs

=

=

Summary of Contents for Stingray






































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands