manualshive.com logo in svg

Allied Stingray, Technical Manual

Share
Download
Allied Stingray Technical Manual Download Page 170

Description of the data path

STINGRAY Technical Manual

 

V4.4.2

170

Standard Update (IIDC)

In the 

Standard Update (IIDC)

 mode single parameter are sent to the cam-

era.

•

Standard Update (IIDC)

 shows same behavior as MARLIN

•

Parameter will be sent from host to camera and will be activated as soon 
as possible without interruption of the transfer

•

If the host updates more than one parameter (without block write) the 
parameters may become active in different images

•

Standard Update (IIDC)

 can be combined with the new parameter 

update timing modes

Camera timing behavior is like this:

Fast Parameter Update Timing

Quick Format Change Mode (QFCM)

After sending a new parameter value, the changed 
parameter value is valid for the available next 
image. Frame rate is constant.

After sending a new parameter value, the changed 
parameter value is valid for the available next 
image.

A running exposure will be interrupted and the 
image is dropped.

There may be a gap between two consecutive 
image transfers.

 Table 52: 

Standard Update (IIDC)

: comparison of 

Standard Format Change Mode

 and 

QFCM

Summary of Contents for Stingray






































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands