Alicat Scientific MC Series Operating Manual Download

Page: 30 / 98

COMM SETUP

Press

COMM SETUP

to adjust the unit ID or baud rate.

UNIT ID

– Valid unit identifiers are the letters

A-Z and @. The identifier allows you to assign a

unique address to each device so that multiple

units can be connected to a single RS-232 or

RS-485 computer port.

Press

UNIT ID

. Use the UP and DOWN buttons to

change the Unit ID. Press SET to record the ID.

Press Reset to return to the previously recorded

Unit ID.

Any Unit ID change will take effect when

SET is pressed.

If the symbol @ is selected as the Unit ID, the

device will enter streaming mode when SET is

pressed. See RS-232 Communications (page 36) for

information about the streaming mode.
BAUD

– Both this instrument and your computer must send/receive data at the

same baud rate. The default baud rate for this device is 19200 baud.

Press

BAUD

. Use the UP and DOWN buttons

to select the baud rate that

matches your computer. The choices are 57600, 38400, 19200, 9600, or 2400

baud. Press SET to record the baud rate.

Any baud rate change will take effect

when SET is pressed..

PRESS AVG

CLEAR

DOWN

BACK/

CANCEL

Avg Time Const: msec

SET

SELECT

DIGIT

001

CLEAR

FLOW AVG

CLEAR

DOWN

BACK/

CANCEL

Avg Time Const: msec

SET

SELECT

DIGIT

127

CLEAR

DOWN

BACK

SET

BAUD

19200

BACK

MAIN

UNIT ID

BAUD

19200

BACK

RESET A

SET

UNIT ID

DOWN

COMM SETUP

BAUD

UNIT ID

Comm:RS232Serial

Summary of Contents for MC Series



































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Operating Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands