Alicat Scientific MC Series Operating Manual Download

Page: 18 / 98

CONTROL

Control

setup is accessed by pressing the button below Control on the Select

Menu display. From this screen you can select your setpoint source, choose a

loop variable and adjust the PID terms.

Press BACK to return to the Select Menu

display.
Press MAIN to return to the MAIN display

SETPT SOURCE

– Pressing the button

above SETPT SOURCE will allow you to

select how the set point will be conveyed

to your controller.
Use the Up and Down buttons to move

the arrow in front of the desired option.

Then press SET.
Press CANCEL to return to the previous

display.
The controller will ignore any setpoint

except that of the selected setpoint source and it will remember which input is

selected even if the power is disconnected.

Serial

refers to a remote digital RS-232

/ RS-485 setpoint applied via a serial

connection to a computer or PLC as

described in the installation and RS-232 /

RS-485 sections of this manual.

Front Panel

refers to a setpoint applied

directly at the controller.

Front Panel input must be selected

prior to changing the setpoint at

the device.

Analog

refers to a remote analog

setpoint applied to Pin 4 of the Mini-DIN

connector as described in the installation

section of this manual.

The standard analog input is 0-5 Vdc.

To determine what type of analog setpoint your controller has, refer to

the Calibration Data Sheet that was included with your controller.

If nothing is connected to Pin 4, and the controller is set for analog control, the

device will generate random setpoint values.
NOTE: If your controller has the

IPC

(Integrated Potentiometer Control) option,

the IPC dial will operate with the ANALOG setpoint source selected.

SETPT

refers to the

setpoint

. This parameter may be changed using the display

only if

FRONT PANEL

is selected as the source. Press

SETPT.

Then use SELECT to

choose the decimal with the arrow and the UP and DOWN buttons to change

the value. Press SET to record your value. Press CLEAR to return to zero.

DOWN

CANCEL

SET

>Serial / FRONT PANEL

ANALOG

LOOP

VAR

BACK

PID

MAIN

SETPT

SOURCE

SETPT

+0.0

Summary of Contents for MC Series



































































































Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands

Alicat Scientific MC Series, Operating Manual

Search results

Summary of Contents for MC Series

Reviews:

Related manuals for MC Series

Brands by name

Popular brands