Alfa Romeo 4C 2016 Page 254 Owner'S Manual Download | Manualshive

Page: 254 / 369

background image

Push the Tire Service Kit power button to the “I” position.
The electric compressor will be turned on, sealant and air
will inflate the tire.

Minimum 26 psi (1.8 bar) of pressure should be reached
within 20 minutes. If the pressure has not been reached
turn off and remove the Tire Service Kit, drive the vehicle
30 feet (10 meters) back and forth, to better distribute the
sealant inside the tire.

Attach the clear flexible filling tube of the compressor
directly to the tire valve and repeat the inflation process.

When the correct pressure has been reached, start driving
the vehicle to uniformly distribute the sealant inside the
tire. After 10 minutes, stop and check the tire pressure. If
the pressure is below 19 psi (1.3 bar), do not drive the
vehicle, as the tire is too damaged, contact the nearest
Authorized Dealer.

WARNING!

Tire Service Kit is not a permanent flat tire repair.
Have the tire inspected and repaired or replaced after
using Tire Service Kit. Do not exceed 65 mph
(110 km/h) until the tire is repaired or replaced.
Failure to follow this warning can result in injuries
that are serious or fatal to you, your passengers, and
others around you. Have the tire checked as soon as
possible at an Authorized Dealer.

If the pressure is at 19 psi (1.3 bar) or above repeat the
inflation process to reach the correct tire pressure and
continue driving.

Peel off the warning label from the bottle and place it on
the dashboard as a reminder to the driver that the tire has
been treated with Tire Service Kit.

252

WHAT TO DO IN EMERGENCIES

«
...
252
253
254
255
256
...
»

Summary of Contents for 4C 2016


















































































































































































































































































































































































Reviews:

No comments

Related manuals for 4C 2016

Brand: iDataLink Pages: 9

Titanium Series

Brand: Fass Pages: 13

Brand: LAMBORGHINI Pages: 48

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

AAB-P-RZR900-K2-001

Brand: SuperATV Pages: 3

Brand: ULTIMATE SPEED Pages: 6

Brand: Toyota Pages: 636

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: Ford Pages: 40

Brand: Axxess Pages: 16

Brand: Brigade Pages: 12

Brand: Maserati Pages: 37

Brand: Whispbar Pages: 77

Brand: Scion Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands