Alfa Romeo 4C 2016 Page 70 Owner'S Manual Download | Manualshive

Page: 70 / 369

background image

WARNING!

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

•

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing (CO),
follow these safety tips:

•

Do not run the engine in a closed garage or in
confined areas any longer than needed to move
your vehicle in or out of the area.

•

If you are required to drive with the trunk/liftgate/
rear doors open, make sure that all windows are
closed and the climate control BLOWER switch is set
at high speed. DO NOT use the recirculation mode.

•

If it is necessary to sit in a parked vehicle with the
engine running, adjust your heating or cooling
controls to force outside air into the vehicle. Set the
blower at high speed.

68

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
68
69
70
71
72
...
»

Summary of Contents for 4C 2016


















































































































































































































































































































































































Reviews:

No comments

Related manuals for 4C 2016

Brand: Acdeos Pages: 38

Brand: Feniex Pages: 6

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

Brand: FormFit Pages: 2

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Ford Pages: 368

Brand: Omix-Ada Pages: 6

Brand: Mercedes-Benz Pages: 91

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Ratio Pages: 12

Brand: Horn Tools Pages: 8

Brand: Ford Pages: 15

Brand: Honda Pages: 3

Brand: Ford Pages: 4378

Brand: Toyota Pages: 549

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands