Alfa Romeo 4C 2016 Page 178 Owner'S Manual Download | Manualshive

Page: 178 / 369

background image

CAUTION!

•

Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with a Alfa Twin Clutch
Transmission cannot be started this way. Unburned
fuel could enter the catalytic converter and once the
engine has started, ignite and damage the converter
and vehicle.

•

To prevent damage to the starter, do not continu-
ously crank the engine for more than 15 seconds at
a time. Wait 10 to 15 seconds before trying again.

After Starting

The idle speed is controlled automatically and it will
decrease as the engine warms up.

Turbo Charger “Cool Down”

This vehicle is equipped with an after-run pump to cool
the turbocharger after the engine is shut off. Depending
on the type of driving and the amount of cargo, the pump
will run for up to five minutes after the engine has been
shut off to circulate coolant through the turbocharger.

Although the pump is rubber-mounted for quiet opera-
tion, it is normal to hear it running during this time.

SIX-SPEED ALFA TWIN CLUTCH TRANSMISSION

WARNING!

•

It is dangerous to shift out of NEUTRAL if the
engine speed is higher than idle speed. If your foot
is not firmly pressing the brake pedal, the vehicle
could accelerate quickly forward or in reverse. You

(Continued)

176

STARTING AND OPERATING

«
...
176
177
178
179
180
...
»

Summary of Contents for 4C 2016


















































































































































































































































































































































































Reviews:

No comments

Related manuals for 4C 2016

Brand: Mazda Pages: 4

Brand: Saab Pages: 75

Brand: Camcar Pages: 6

Brand: FormFit Pages: 2

Brand: WABCO Pages: 32

Brand: cam Pages: 28

Brand: Gator Pages: 6

Brand: Prorack Pages: 15

Brand: Buick Pages: 20

Brand: Wallbox Pages: 21

Brand: Technaxx Pages: 59

Brand: iDataLink Pages: 11

Brand: Ford Pages: 722

Brand: Edelbrock Pages: 1

Brand: Toyota Pages: 422

Brand: AirBedz Pages: 4

Brand: Jensen Pages: 2

Brand: Vauxhall Pages: 325

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands