Alfa Romeo 4C 2016 Page 191 Owner'S Manual Download | Manualshive

Page: 191 / 369

background image

System Failure

In the event of system failure or a fault with the gear
selector, no driving modes can be selected.

The display will become grey (same screen as

⬙

Natural

⬙

mode) but without an indication of the Alfa DNA setting.
The display will also show a warning message.

Please contact your authorized dealer for service.

Launch Control

The Launch Control strategy permits high-performance
acceleration from stand still.

This strategy can be activated with vehicle at a standstill,
Race mode selected and FIRST (1st) gear engaged.

The sequence of operations to perform is as follows:

1. Press the brake pedal and hold it down.

2. Press the accelerator pedal and hold it down.

3. Press the

⬙

–

⬙

paddle behind the steering wheel. (This

allows the engine to rev above the 3000 RPM limit.)

When the brake pedal is released, the vehicle will start
with maximum acceleration. Despite the MANUAL
mode, the vehicle will automatically shift the gear to
guarantee maximum acceleration, once the correct shift-
ing speed has been reached.

WARNING!

Launch Control is intended for off-highway or off-
road use only and should not be used on any public
roadways. Use Launch Control only in a controlled
and dry track environment; within the limits of the
law. Actual Launch Control performance may change
depending on the surface and current traction condi-
tions. The capabilities of the vehicle as measured by
the performance pages must never be exploited in a

(Continued)

5

STARTING AND OPERATING

189

«
...
189
190
191
192
193
...
»

Summary of Contents for 4C 2016


















































































































































































































































































































































































Reviews:

No comments

Related manuals for 4C 2016

Brand: Daihatsu Pages: 1718

Brand: Camcar Pages: 6

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: Subaru Pages: 3

Brand: Mobile Create Pages: 15

Brand: Vintage Air Pages: 28

Brand: BMW Pages: 21

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

2011 3500 Chassis Cab

Brand: RAM Pages: 92

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: UAZ Pages: 112

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: v.link Pages: 12

Brand: ConWys AG Pages: 16

2008 B2300 Truck

Brand: Mazda Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands