background image

Version April 2008

EN

 25

agru SP 315-S User’s Manual

All machines that are new or newly programmed during maintenance or upon 
request is wished are shipped with the most recent software version.

Lubrication of 

s"ALL'UIDE"USHINGS
s2UNNER"LOCKS
s$RIVE3PINDLE

The 4 ball guide bushings of the support console of the facing tool and 
heating element and the 2 runner blocks of the heating element and 4 
runner blocks of the facing tool, as well as the 4 runner block of the mov-
able carriage of the machine (see the photos and the machine description 
in section 3) have to be lubricated regularly, every 12 months.

The same holds for the ball-bearing drive spindle ensuring longitudinal 
movement of the support console, which is accessible in the equipment 
and storage cabinet. 

However, this spindle must only be lubricated by 

trained staff.

 Damage due to inadequate, improper, or lack of lubrication 

are not eligible for warranty.

Lubricant and lubricant gun, which both are fully matched to the lubrica-
tion the machine needs, can be ordered with the manufacturer/distributor. 

It is unacceptable to use other lubricants than the dedicated product 
approved of by the manufacturer.

 The application of common grease 

products or widely available general lubricants may cause serious damage 
to the machine and make it unfit for further use.

In the equipment and storage cabinet you will also find the fuses and the 
automatic  safety  switch  for  the  heating  element,  facing  tool,  and 
facing tool motor

.

Info

We reserve the right to change technical specifications of the 
unit without prior notice.

P.O. Box 1108 • 655 Andover St.,Lawrence, MA  01843 • Tel: (800) 343-3618, (781) 321-5409

Fax: 800-787-6861• Website: www.asahi-america.com • Email: [email protected]

Service and Repair Contact

 A

sahi/America

655 Andover St.

Lawrence, MA 01843

1-800-343-3618

[email protected]

Summary of Contents for SP 315-S



























Reviews: