background image

>>

<<

ATH778-5678-315CC

Version April 2008

22 

EN

agru SP 315-S User’s Manual

Distance Error

The stroke of the carriage (at facing, change-over, or 
joining) does not correspond to the expected distance it 
should travel; welding has to be repeated.

Force Error

The applied force is out of tolerance; welding has to be 
repeated.

Power Supply Failure

In the course of the last welding operation, a power 
supply failure occurred; welding has to be repeated.

Emergency Stop

The welder has turned the machine off using the 
Emergency Stop switch. If this was done because of a 
malfunction of the machine, it must not be turned on 
again, unless it is beyond doubt that it works properly.

Mirror Temperature Low

The mirror temperature is out of tolerance and cannot 
be adjusted; as long as this error is not cleared, welding 
or repeating a welding operation is not possible.

Printing and Transferring Welding Reports

The machine is equipped with USB A interface that gives you the op-
portunity to connect the tag printer or, if permitted, a USB stick and a 
USB B interface through which data can be 
transferred to a PC, e.g. with an installation 
of the DataWork agru software.

5.1 

The Print Menu and Printing/
Transferring Reports

When a data communication cable is con-
nected while the standard data screen (see 
Display  5) is showing, the machine displays 
the print menu. According to the selection 
made on this menu, data will be sent to the 
connected device: to the a printer for print-
out or to a PC for further processing and 
archiving.

Touch the appropriate button to select print-
ing “All Reports”, printing “By Commission 
Number”, or printing “By Date”.

The option “All Reports” causes all the welding reports stored in system 
memory to be printed. While the machine transfers the reports, a count-
down indicates how many of them remain to be printed or transferred.

The options “By Commission Number” and 
“By Date” lead the operator to the next 
screen in which arrow buttons can be used 
to browse through the repor ts in system 
memory to select the desired commission 
or date from which reports should be printed 
or transferred (see Display  19). The options 
show the first available commission number 
or date, and once the desired one is found, 
the selection has to be confirmed by “Ok” to 
start the transfer to printer or PC.

If the machine displays a “Printer not Ready” 
error message after you touched the “Ok” 
button, the printer has to be switched to on-

Display 18

Print Menu

Cancel

agru SP 315-S    26.04.08   15:32

+16°C

All Reports

By Commission Number

By Date

Display 19

Select Commission Number

Cancel

agru SP 315-S    26.04.08   15:33

+16°C

Ok

Summary of Contents for SP 315-S



























Reviews: