7-25
Acquire Commands
SRATe (Sample RATe)
SRATe (Sample RATe)
Command
:ACQuire:SRATe {AUTO | MAX | <rate>}
The :ACQuire:SRATe command sets the acquisition sampling rate for real time
and peak detect sampling modes. If the oscilloscope is in the equivalent time
sampling mode, the SRATe command has no effect on the sampling rate.
However, if you change the sampling mode to one of the real time sampling
modes the control will show the new value.
AUTO
The AUTO rate allows the oscilloscope to select a sample rate that best
accommodates the selected memory depth and sweep speed.
MAX
The MAX rate enables the oscilloscope to select maximum available sample rate.
<rate>
A real number representing the sample rate. You can send any value, but the
value is rounded to the next fastest sample rate.
Interaction between :ACQuire:SRATe and :ACQuire:POINts
If you assign a sample rate value with :ACQuire:SRATe or a points value using
:ACQuire:POINts the following interactions will occur. “Manual” means you are
setting a non-AUTO value for SRATe or POINts.
Table 7-9
Available Sample Rate Values (in Sa/s)
Example
This example sets the sample rate to 250 MSa/s.
10 OUTPUT 707;":ACQUIRE:SRATE 250E+6"
20 END
SRATe
POINts
Result
AUTO
Manual
POINts value takes precedence (sample rate is limited)
Manual
AUTO
SRATe value takes precedence (memory depth is limited)
Manual
Manual
SRATe value takes precedence (memory depth is limited)
0.5
1
2
2.5
4
5
10
20
25
40
50
100
200
250
400
500
1k
2k
2.5k
4k
5k
10k
20k
25k
40k
50k
100k
200k
250k
400k
500k
1M
2M
2.5M
4M
5M
10M
20M
25M
40M
50M
100M
125M
200M
250M
500M
1G
2G
4G
Summary of Contents for Infiniium 8000A
