2- 3
LAN and GPIB Interfaces
LAN Interface Connector
LAN Interface Connector
The oscilloscope is equiped with a LAN interface RJ-45 connector on the rear
panel. This allows direct connect to your network. However, before you can
use the LAN interface to program the oscilloscope, the network properties must
be configured. Unless you are a Network Administrator, you should contact
your Network Administrator to add the appropriate client, protocols, and
configuration information for your LAN. This information is different for every
company.
GPIB Interface Connector
The oscilloscope is equipped with a GPIB interface connector on the rear panel.
This allows direct connection to a GPIB equipped computer. You can connect
an external GPIB compatible device to the oscilloscope by installing a GPIB
cable between the two units. Finger tighten the captive screws on both ends
of the GPIB cable to avoid accidentally disconnecting the cable during
operation.
A maximum of fifteen GPIB compatible instruments (including a computer) can
be interconnected in a system by stacking connectors. This allows the
oscilloscopes to be connected in virtually any configuration, as long as there is
a path from the computer to every device operating on the bus.
C A U T I O N
Avoid stacking more than three or four cables on any one connector. Multiple
connectors produce leverage that can damage a connector mounting.
Summary of Contents for Infiniium 8000A
