manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 87

Agilent Technologies Helium Leak Detector 

DRAFT 12/1

1

/17

87

Test Time

 

This setting tells the system when to perform the test against the set 
point values. For example, you may set 20 seconds for the 

Test 

Time

. At the end of 20 seconds, the system determines if the part 

has passed or not and then makes an indication by either going to 

VENT

 (Pass) or going to 

HOLD

 (Fail) and displaying the reject set 

point failure on the 

Home 

screen. The final leak rate value appears 

on the 

Home

 screen regardless of a pass or failed criteria. The next 

test cycle (pressing 

Test

) clears the leak rate value (setup below).

NOTE

The Test, Vent and Zero functions are available in this 
application setup. The Test and Vent buttons aid in setting up 
the Rough and Test Timers. The Zero function is extremely 
helpful in zeroing out unwanted background associated with 
the test fixture. The zeroing set up helps in reducing the test 
time.

5.1.3.8.2  Auto Sequencer Set-Up

Attach the test fixture with the part to be tested (known good test object) on to the leak 
detector test port.

5.1.3.8.2.1  Rough Time Setup

Determines the amount of allowable time for the leak detector to evacuate the test object to 
the 

Transfer Point

 - 

Transfer Pressure

.

To test:

1. Select 

Test Configurations > Advanced Features > Setup.

If the transfer pressure is not achieved within the pre-selected rough time, the system 
aborts the cycle and goes into 

Hold

 mode.

NOTE

Factory Default - Transfer Point (Transfer to Test Pressure) is 1 
Torr 

Do not activate or program any 

Set Points

.

2. Program the 

Rough Timer

 for some unrealistic amount of time, like 200 secs.

3. Program 

Test Time

 for 30 secs and press 

Test

.

Allow the test to complete (system vents).

4.

Program the Rough Time as displayed in the Rough

 

Time

 window. 

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands