manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 16

Agilent Technologies Helium Leak Detector 

16

DRAFT 12

/1

1/17

O-ring Care

When removing, checking or replacing O-rings, keep in mind the following:

NOTE

Agilent recommends replacing all O-rings during routine 
maintenance or during any maintenance procedure requiring 
that O-rings be removed.

NOTE

Due to the effective cleaning nature of VacuSolv solvent and 
its residue-free properties, Agilent’ Component and 
Spectrometer Cleaning Kit (Part Number 670029096), used in 
accordance with the kit instructions, is recommended for 
cleaning spectrometer components. The kit can also be used for 
fine cleaning of other parts in the leak detector’s vacuum 
system such as valves and fittings. No rinsing steps or 
high-temperature drying are required following cleaning with 
VacuSolv. Although appropriate precautions are advised, 
VacuSolv is compatible with most materials and does not 
contain toxic chemicals or CFCs (chlorofluorocarbons). Other 
acceptable solvents are isopropyl alcohol (IPA) or Dow 
Corning

®

 OS-20.

CAUTION

Remove O-rings carefully with your fingers. Do not use metal 
tools for this task; this prevents scratching of any sealing 
surfaces.

❑

Wipe all O-rings clean with a lint-free cloth before 
installation to ensure that no foreign matter is present to 
impair the seal.

❑

Do not use grease or any other substance on O-rings that 
will come in contact with the spectrometer.

❑

Do not use alcohol, methanol or other solvents on O-rings. 
Doing so causes deterioration and reduces their ability to 
hold a vacuum.

❑

Agilent does not recommend the use of vacuum grease. If 
applicable, apply a small amount of Apiezon

®

 L grease and 

wipe the O-rings shiny dry.

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands