manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 143

Agilent Technologies Helium Leak Detector 

DRAFT 12/1

1

/17

143

Table A-1 lists inquiries that are used to determine internal operating parameters. 
All inquiries, except VER, begin with 

?

 and end with <CR>.

Table A-1  Internal Operating Parameters 

Inquiry

Response

?ALL

Responds with four lines. Each begins with a <cr><lf>. The first line 
reports the ion chamber value. The second line reports the emission value. 
The third line reports the value of the offset variable. The fourth line reports 
the gain value.

?AZ<0

Reports the status of the Auto-zero < 0 function, ON or OFF.

?CALOK

Reports the status of the last calibration.

?CL-XFER

Reports the currently stored contra-flow mode crossover pressure.

?CPLOCKOUT

Reports the status of the control panel lockout feature, ON or OFF.

?CURRDATE

Reports the current system date and time in the following format: 3 
05/25/2005 04:19:03.35 1 where 3 is the day of the week (0 = Sunday, 1 = 
Monday, etc), 05/25/2005 is mm/dd/yyyy (date), 04:19:03.35 is 
hh/mm/ss/ms (time) and 1 is PM (0=AM, 1=PM, 2=24 hour).

?DISPLAY

Reports what the display bar graph is set to, 

log

 or 

lin

.

?EMISSION

Reports the emission value.

?EXPONENT

Reports the current manual-mode exponent with a two-character (minus 
followed by one digit) number. The exponent is within the least sensitive 
range (as reported by ?RANGE) and the three lower (more negative 
exponent) ranges. See also INIT-EXPONENT.

?EXTLEAK

Reports the currently stored value of the external standard leak.

?GAIN

Reports the system gain value by returning a three-character number 
consisting of a two-digit gain factor with a decimal point after the first digit.

?INTEXT

Indicates which leak, Internal or External has been selected for use during 
calibration.

?IOBOARD

Returns the status:  0 = not installed, 1 = installed

?IO_VER

Returns the software revision of the installed I/O PCB

?IONCHAMBER

Reports the ion chamber value.

?LANGUAGE

Reports the language that has been selected to display on the front panel 
(0=English, 1=French, 2=German, 3=Korean, 4=Spanish, 5=Japanese, 
6=Chinese or Russian depending on software version purchased).

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands