manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 77

Agilent Technologies Helium Leak Detector 

DRAFT 12/1

1

/17

77

5.1.2.4  Home Screen - Activate Gross Test

Figure 5-5  Home Screen - Activate Gross Test

Gross Test

Allows the operator to locate leaks while the system is in roughing 
mode. The test indicates the presence of a leak at high pressures 
only and does not display a leak rate value.

1. Activate Gross Test.

The GROSS TEST button appears on the Home screen when the 
test port pressure is between 10 and 150 Torr. 

2. Press GROSS TEST to enter the screen.

❑

There is an audio tone for Gross Leak testing, which 
increases as the leak increases.

❑

Gross Test only works when the test port pressure is between 
10 and 150 Torr and remains constant (± 2% between 
previous and current pressure readings). 

❑

The Gross Leak test stops if the system goes into Backing, 
Test or Fine TEST mode.

❑

Activating the Auto Sequencer button terminates the Gross 
Leak test.

❑

The HOLD button is inactive while in Gross Leak test mode, 
as the system is in roughing mode.

Press to activate 
Gross Test.

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands