manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 106

Agilent Technologies Helium Leak Detector 

106

DRAFT 12

/1

1/17

Figure 6-3  Settings: Screen Settings

Buttons and Fields

Bar Graph

Configures the bar graph:

❑

Linear Scale

 - The linear bar graph leak rate appears across 

the top of all screens when selected. In the 

Linear Bar

 Graph 

display mode, the bar graph display represents the mantissa 
of the leak rate, spanning from 

0

 to 

10

. The numerical 

display (located to the upper right of the bar graph) indicates 
the leak rate exponent value. This mode offers exceptional 
resolution within a decade.

❑

Log Scale

 - The log bar graph leak rate appears across the 

top of all screens. In 

Log Bar Graph

 display mode, the bar 

graph display represents the entire leak rate range of the leak 
detector, spanning from E-11 atm cc/sec to E-4 atm cc/sec. 
The numerical display (located to the upper right of the bar 
graph) is not lit in this mode.

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands