manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 128

Agilent Technologies Helium Leak Detector 

128

DRAFT 12

/1

1/17

7.4.1  Current Setup Menu

Details of the current leak detector setup are displayed. Reject and audio set point status, 
auto sequencer status & split flow. The calibrated leak setting, leak rate range settings and 
vent lock out status.

Figure 7-15  Current Setup Screen

a

Table 7-3  Current Setup Screen Conditions 

Condition

Display

Description

Audio Set Point

See Section 7.4.1 “Current Setup 
Menu” on page 128.

Audio Set Point: 
Active

Audio Set Point is active.

Audio Set Point: 
Inactive

Audio Set Point is inactive.

Auto Sequencer

See Section 7.4.1 “Current Setup 
Menu” on page 128.

Auto Sequencer: On

Auto Sequencer (automatic test cycle) 
is enabled.

Auto Sequencer: Off

Auto Sequencer (automatic test cycle) 
is disabled.

Calibration Set-Up

See Section 4 “Calibration Screen” 
on page 65.

Int Cal Leak

System is set to calibrate to the internal 
standard leak.

Ext Cal Leak

System is set up to calibrate to an 
external standard leak.

Leak Rate Range

See Section 4 “Calibration Screen” 
on page 65.

Auto Ranging

System is set to auto range through 
the leak rate scale.

Manual Ranging

System is set for manual range control.

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands