manualshive.com logo in svg

Agilent Technologies G8610A, Operation Manual

Share
Download
Agilent Technologies G8610A Operation Manual Download Page 18

Agilent Technologies Helium Leak Detector 

18

DRAFT 12

/1

1/17

WARNING

Equipment tightness is guaranteed for normal operating 
conditions when the equipment leaves the factory. It is the 
user’s responsibility to maintain the level of tightness, 
particularly when pumping dangerous products.

CAUTION

The performance and operating safety of this equipment can 
only be guaranteed if it is operated according to normal 
conditions of use.

Allow at least 2 to 3 feet of clearance adjacent to the slots at the 
front, sides and back of the equipment enclosure.

Allow sufficient room for the operator to safely maneuver to 
perform testing.

Touch Panel Display

CAUTION

Do not apply excessive pressure to the Touch Panel display as this 
may cause smears. 

In general, the lower the temperature, the longer it takes the Touch 
Panel display to turn on. Performance of the Touch Panel display 
may deteriorate in low temperature.

Radio

The Wireless Remote Control and Base Board PCB are built around 
Laird's, model RM024, RF transceiver module operating in 2.4 
GHz ISM band. The same type of the RF module is built in an Agi-
lent Technologies Helium Mass Spectrometer Leak Detector Wire-
less Base Station PCB and Wireless Remote unit (see 

Agilent 

Technologies Helium Mass Spectrometer Leak Detector Wireless 
Remote Operational Manual

 (6999099945A)).

Agency Identification Numbers for Laird, Model: RM024 
AC4424-100:

❑

US/FCC ID: KQL-RM024

❑

CAN/IC: RSS-210

❑

EUR/ETSI EN: CE

❑

Taiwan: CCAI13LP3400T1, CCAI13LP3330T3

are also applied to the Agilent's Wireless Remote and Agilent Tech-
nologies Helium Mass Spectrometer Leak Detector Wireless Base 
Station, when the units are used the approved antennas.

Summary of Contents for G8610A

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands