Agilent Technologies E5022A Operation Manual Download Page 437

Page: 437 / 453

436

Appendix H

Ramp Load

Ramp Load

suddenly. It is more dangerous, when the plug for air stopper blows off from the air
fitting.

Figure H-6

Plug the Air Fitting using Air Stopper Assembly

The LED on it shows the status of the ramp loading mechanism. Assignment of the LED is
as follows.

Ramp Cylinder Installation

Install the ramp cylinder assembly to the ramp rail assembly.

For UP face, tighten the two screws with 2.0 mm hex key to install the ramp cylinder
assembly to the ramp rail assembly as shown in Figure H-7.

For DOWN face, tighten the two screws with 2.0 mm hex key to install the ramp cylinder
assembly to the ramp rail assembly as shown in Figure H-8.

Table H-2

LED Assignment

LED

Description

Power

When DC 24V is supplied from the power supply unit, LED is
illuminated.

Tilt

When switch is set to “Tilt”, LED is illuminated.

Ramp

When switch is set to “Ramp”, LED is illuminated.

Error

This LED is illuminated under the following situation.

•

The system performs the Ramp In, But the ramp is still in Ramp Out
position.

•

The system performs the Ramp out, But the ramp is still in Ramp In
position.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for E5022A






































































































































































































































































































































































































































































Search results

Summary of Contents for E5022A

Reviews:

Related manuals for E5022A

Brands by name

Popular brands

Agilent Technologies E5022A, Operation Manual

Search results

Summary of Contents for E5022A

Reviews:

Related manuals for E5022A

Brands by name

Popular brands