manualshive.com logo in svg

Agilent Technologies E5022A, Operation Manual

The Agilent Technologies E5022A is a cutting-edge testing instrument for precise measurements. For detailed instructions on how to operate this device, download the free Operation Manual from manualshive.com. With this manual, users can effortlessly navigate through the features and functions of the E5022A for optimal performance.

Share
Download
background image

80

Chapter 3

 

VEE Measurement Program Operation

Measurement

Read Ratio  

Specifies the read aperture ratio relative to its 
corresponding sector (segment). See “Stability 
Measurement” on page  248.

Curr. Mode  

Specifies the current polarity. When “Normal 
Mode” is selected, write current polarity is the 
same as read current polarity. If “Reverse 
Mode” is selected, the read current polarity is 
opposite to the write current polarity. Some 
head amplifier does not support the reverse 
and/or off functions. This setting is used for 
only the stability measurement. The other 
measurements use the setting of Sense Curr. 
Mode under the setup menu for the current 
polarity. See Figure 3-10 on page  53.

4. Click on the [Write Config] button, to set the stimulus write pattern of the stability 

measurement.

In order to effectively use the write mode “continuous” you must set the repetitive 
period of the selected data pattern to 1T, 2T, 4T and/or 8T in the [Pattern Config] menu. 
Refer to the “hpe5022_stabilityWriteModeConfig” function of the programming 
manual for details.

Figure 3-34 

Stability Write Configuration Menu

NOTE

If the attached head amplifier does not support “continuous” write current function, a 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for E5022A






































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for E5022A

Raymarine i70 Installation & Operation Instructions preview
i70
Brand: Raymarine Pages: 90
QBC Diagnostics Star Operators & Service Manual preview
Star
Brand: QBC Diagnostics Pages: 65
Echo WT-1610 Instruction Sheet preview
WT-1610
Brand: Echo Pages: 6
Echo Pro Attachment Series Manual preview
Pro Attachment Series
Brand: Echo Pages: 28
Echo BRD-280 Specifications preview
BRD-280
Brand: Echo Pages: 2
Ecco Pro Vantage 12+ Series Mounting Instructions preview
Pro Vantage 12+ Series
Brand: Ecco Pages: 6
Waterous Pressure Governor Installation And Operation Manual preview
Pressure Governor
Brand: Waterous Pages: 53
Landi Renzo V05 Instruction Manual preview
V05
Brand: Landi Renzo Pages: 16
IBM 727 Manual Of Instruction preview
727
Brand: IBM Pages: 163
Velp Scientifica ECO 8 Operation Manual preview
ECO 8
Brand: Velp Scientifica Pages: 12
Yamaha D24 Upgrade Manual preview
D24
Brand: Yamaha Pages: 24
J&M Nitro Gro 5010 Assembly Manual preview
Nitro Gro 5010
Brand: J&M Pages: 33
QRS PMII Upgrade Instructions preview
PMII
Brand: QRS Pages: 16
QMAXZ Lighting QS Series User Manual preview
QS Series
Brand: QMAXZ Lighting Pages: 36
Makita WA400MP Instruction Manual preview
WA400MP
Brand: Makita Pages: 208
Tarmo 602456 Manual preview
602456
Brand: Tarmo Pages: 4
Abus TAS 112 Installation And Operating Instructions Manual preview
TAS 112
Brand: Abus Pages: 8
ABB HT614812 Operation Manual preview
HT614812
Brand: ABB Pages: 112

Brands by name

Popular brands

Load more brands