AGI 15100SA Assembly Manual Download Page 43

Page: 43 / 82

P1512161 R0

Figure 33.

Installing the Hydraulic Motor

Install the Hydraulic Fittings and Coupler Guard

1. Insert the 1/2" x 3/8" nipple (2) into the input (pressure) port and 1/2" swivel (1) into the return port of the

hydraulic motor. See

Figure 34

2. Insert the 1/2" check valve (3) into the 1/2" x 3/8" nipple (1).

3. Insert 1/2" swivel (1) into the check valve.

4. Install the coupler guard (6) using 1/4" self-tapping screws (4) and 1/4" flat washers (5).

Table 15.

Hydraulic Fittings and Coupler Guard Components

Item

Description

1/2" x 3/8" Hex Nipple (S1022DC)

Swivel 90 - 1/2" Straight

1/2" Check Valve (No Rev Flow)

1/4" Self-tapping Screw

1/4" Flat Washer

1-1/4" Hydraulic Motor Guard 4.5 x 6.25

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Summary of Contents for 15100SA



















































































Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands

AGI 15100SA, Assembly Manual

Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands