AGI 15100SA Assembly Manual Download Page 8

Page: 8 / 82

P1512161 R0

1.5.2 Hydraulic Power Safety

Power Source

• Refer to the rules and regulations applicable to the power

source operating your hydraulic drive.

• Do not connect or disconnect hydraulic lines while system is

under pressure.

• Keep all hydraulic lines away from moving parts and pinch

points.

• Escaping hydraulic fluid under pressure will cause serious

injury if it penetrates the skin surface (serious infection or
toxic reaction can develop). See a doctor immediately if
injured.

• Use metal or wood as a backstop when searching for

hydraulic leaks and wear proper hand and eye protection.

• Check all hydraulic components are tight and in good

condition. Replace any worn, cut, abraded, flattened, or
crimped hoses.

• Clean the connections before connecting to equipment.

• Do not attempt any makeshift repairs to the hydraulic fittings

or hoses with tape, clamps, or adhesive. The hydraulic
system operates under extremely high pressure; such repairs
will fail suddenly and create a hazardous and unsafe
condition.

Lockout

• Always place all hydraulic controls in neutral and relieve

system pressure before disconnecting or working on
hydraulic system.

1. SAFETY

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

Summary of Contents for 15100SA



















































































Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands

AGI 15100SA, Assembly Manual

Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands