AGI 15100SA Assembly Manual Download Page 55

Page: 55 / 82

P1512161 R0

3.18. Install the Basic Hopper Wheel (Optional)

This section is applicable to the Swing Away models without hydraulic or electric power swing options.

1. Attach the wheel mount (2) to the hopper weldment (1) using 1/2" x 1-1/2" bolts (7) and 1/2" locknuts (8).

See

Figure 47

2. Attach each tire (6) to the wheel mount weldment (2) using a 3/4" x 6" bolt (3), seven 3/4" flat washers (5),

and a 3/4" locknut (4).

Table 22.

Hopper Wheel Components

Item

Description

Quantity

Transfer Hopper Assembly

Swing Transfer Wheels Front Mount

3/4" x 6" Hex Bolt

3/4" Nylock Nut

3/4" Flat Washer Plated USS

Tire

1/2" x 1-1/2" Bolt

1/2" Nylock Nut

Figure 47.

Installing Hopper Wheel

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Summary of Contents for 15100SA



















































































Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands

AGI 15100SA, Assembly Manual

Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands