AGI 15100SA Assembly Manual Download Page 46

Page: 46 / 82

P1512161 R0

3.15. Assemble the Main Conveyor Boot

Install the Boot Flashing

1. Attach foam tape onto the hopper weldment. See

Figure 36

Figure 36.

Foam Tape

2. Drill 3/8" holes through the foam tape using the existing hopper holes as guides.

3. Apply glue underneath the flashing pieces as shown in

Figure 37

4. Place the front flashing onto the hopper.

5. Place the side flashing on top of the front flashing.

6. Make sure all flashing pieces are flush. Ensure that there are no gaps between the flashing and the belt.

Secure into place until the Swing Away is mounted on.

Figure 37.

Rubber Flashing

The main conveyor hopper is now ready for the installation of the boot base.

3. ASSEMBLY

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

Summary of Contents for 15100SA



















































































Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands

AGI 15100SA, Assembly Manual

Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands