AGI 15100SA Assembly Manual Download Page 31

Page: 31 / 82

P1512161 R0

3.11. Install the Collapsible Hopper Cloth

Install the Flashing

1. Lay the front flashing (1) on the hopper while ensuring it is flush with the edge of the main hopper frame

(see

Figure 20

Note

The textured side of the flashings should be facing down.

2. Install transition flashing (3) using 1/4" x 1" self-tapping screws (4), 1/4" flat washers (5), 1/4" x 1-1/4"

flange bolts (6), and 1/4" hex nuts (7).

3. Lay the side flashings (2) on the hopper while ensuring they are flush with the edge of the main hopper

frame and overlapping the front flashing.

Table 7.

Flashings

Item

Description

Front Flashing

Side Flashing

Transition Flashing

1/4" x 1" Self Tapping Screw

1/4" Flat Washer

1/4" x 1-1/4" Flange Bolt

1/4" Hex Nut

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Summary of Contents for 15100SA



















































































Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands

AGI 15100SA, Assembly Manual

Search results

Summary of Contents for 15100SA

Reviews:

Related manuals for 15100SA

Brands by name

Popular brands