Affirmative YEStablet 7370 User Manual Download Page 53 | Manualshive

Page: 53 / 104

background image

Connection icon if the connection is lost or if the YES

tablet

7370 is not properly seated on the

cradle. The button needs to be engaged again to re-establish a lost or improper connection.

Connection

Established Connection

Not

Established

Wireless Network Card Antenna System

The YES

tablet

7370 has a PC Card slot along the upper left edge of the device. This slot houses the

wireless LAN adapter. This slot may be left open for the user to insert a Cisco Aironet 350 adapter, or
the YES

tablet

7370 may be delivered with an embedded Z-Com card with a custom antenna in a snap-

type housing. In the latter case, the user has the choice of leaving the antenna in the snap-on position
(A) or of pulling the antenna tip off the retainer snap in order to obtain better wireless connectivity
through varying orientations up to near vertical (B).

(A)

(B)

Dynamic Display Rotation

The YES

tablet

7370 allows dynamic rotation of the display in 90-degree increments. Double-click on

the Desktop icon and then select the desired rotation from the Screen Rotation window. The rotation
change will be effected immediately, without needing to re-start the 7370. Invoking a rotation change
may not fully apply to applications that are already open.

Software Installation and
Synchronization (ActiveSync)

The YES

tablet

7370 is amenable to software installation and synchronization through connection to a

host PC. Connection can be made with a USB cable between the host PC and the USB Slave port on
the cradle of the YES

tablet

7370. Connect as follows:

1. Install Microsoft’s ActiveSync 3.6 or above on the host PC. You can download this program from

http://www.microsoft.com/mobile/pocketpc/downloads/activesync36.asp

39

«
...
51
52
53
54
55
...
»

Summary of Contents for YEStablet 7370









































































































Reviews:

No comments

Related manuals for YEStablet 7370

Brand: Harman Kardon Pages: 8

Brand: Wacom Pages: 2

Brand: Wacom Pages: 2

Brand: Wacom Pages: 2

Brand: Wacom Pages: 2

Brand: Wacom Pages: 49

Brand: Wacom Pages: 63

Brand: Wacom Pages: 2

Brand: Wacom Pages: 65

Brand: Wacom Pages: 34

Brand: Wacom Pages: 2

Brand: Wacom Pages: 2

Brand: Wacom Pages: 56

Brand: Wacom Pages: 2

Brand: Wacom Pages: 4

Brand: Wacom Pages: 163

Brand: Acecad Pages: 19

Brand: CHENGDU VANTRON TECHNOLOGY Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands