Affirmative YEStablet 7370 User Manual Download Page 23 | Manualshive

Page: 23 / 104

background image

when using an Aironet card with a non-Cisco access point. If you must use a non-Cisco access
point, be sure that your Aironet card firmware is at level 5.02.19 or above; this will overcome
some of the degradation. Also, bring your access point up to its latest firmware.

Aironet Client Utility (ACU)

This utility is used to configure the myriad of wireless parameters for the Cisco adapter, as well as to
display connection information. Detailed instructions can be obtained from the Cisco web site at

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/index.htm

but we will cover the basics here. Open this utility from

My Computer

Æ

Control Panel

Æ

Wireless

Network Card

or by clicking down the path

Start

Æ

Programs

Æ

Cisco

Æ

ACU

. You will see a

window with five tabs.

Note:

If you are connected to an access point when you open ACU, you will be automatically

disconnected. After you close ACU, you can initiate a connection by momentarily entering and then
exiting the Suspend Mode.

Profiles

Most of the configuration is done under this tab. Multiple profiles can be defined, since it may be
necessary to have a different set of parameters for different networks or for different users. The default
is to start with one active profile,

Profile0

. Buttons are available to

Rename

or

Edit

this profile, or to

Add

more profiles. If there are multiple profiles, you can

Delete

some if you wish. The Select Active

Profile field allows you to select the current active profile. The

Options

button allows you to select %

or dbm as the measurement unit when signal strength is displayed. The

About

button shows the ACU

version.

Highlight a profile in the Manage Profiles sub-window and click on

Edit

to set the configuration

parameters for that profile.

Edit

The entire profile configuration is done here. When you click on

Edit

, you will see a Profile Properties

sub-window. Select a property in the Property box, and the existing value for that property will appear
in the Value box. If there are predefined value choices for a property, a drop-down list will appear for
your selection in the Value box. Otherwise, you can enter alphanumeric characters into that box, or
change existing characters.

A description of each property is given in the following table.

9

«
...
21
22
23
24
25
...
»

Summary of Contents for YEStablet 7370









































































































Reviews:

No comments

Related manuals for YEStablet 7370

Brand: NEC Pages: 29

Brand: Dual Pages: 18

Brand: Vonino Pages: 28

Brand: Wacom Pages: 2

Brand: Curtis Pages: 47

Brand: Sony Pages: 2

Brand: Sony Pages: 52

Brand: Sony Pages: 51

Tablet Z Xperia SGP321

Brand: Sony Pages: 121

Brand: Sony Pages: 185

Brand: Sony Pages: 321

Brand: Spectra Pages: 5

Brand: RCA Pages: 26

STUDIOMASTER T700

Brand: Revox Pages: 16

Brand: Tatung Pages: 37

Brand: Renkforce Pages: 84

Brand: Jay-tech Pages: 27

Brand: BungBungame Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands