Affirmative YEStablet 7370 User Manual Download Page 33

Page: 33 / 104

Statistic Description

Unicast Packets

The number of unicast packets that were transmitted successfully.

Bytes Transmitted

The number of bytes of data that were transmitted successfully.

Packets Retry Long

The number of normal data packets that were retransmitted.

Packets Retry Short

The number of request-to-send (RTS) packets that were retransmitted.

Packets Max Retries

The number of packets that failed to be transmitted successfully after
exhausting the maximum number of retries.

Up Time (hh:mm:ss)

The amount of time (in hours:minutes:seconds) since your client adapter
was started. If the client adapter has been running for more than 24 hours,
the time is displayed in days, hours:minutes:seconds.

Table 4. Aironet MIC Statistics Definitions

Statistic Description

Packets MIC OK

The number of packets that were received successfully with a valid MIC.

Packets No MIC

The number of packets that were discarded due to no MIC being found.

Packets Incorrect
MIC

The number of packets that were discarded due to an incorrect MIC value.

Packets No MIC Seed

The number of packets that were discarded due to no MIC seed being
received.

Packets Wrong MIC
Seq

The number of packets that were discarded due to the MIC sequence number
being wrong.

Summary of Contents for YEStablet 7370









































































































Search results

Summary of Contents for YEStablet 7370

Reviews:

Related manuals for YEStablet 7370

Brands by name

Popular brands

Affirmative YEStablet 7370, User Manual

Search results

Summary of Contents for YEStablet 7370

Reviews:

Related manuals for YEStablet 7370

Brands by name

Popular brands