AEMC 6417 User Manual Download Page 16

Page: 16 / 52

Clamp-on Ground Resistance Tester Model 6417

2.8 Button Functions

Button

Description

▲

• When the rotary switch is set to

+A or A:

Increases the brightness

of the display, making it easier to read the display in an environment with

strong background illumination. Highlighting activated for 30 seconds.

• When the rotary switch is set to SET-UP or

MR:

Serves as the

▲

arrow when browsing in the menus and values. The brightness of the

display does not change when device is set to

SET-UP

MEM

▼

• When the rotary switch is set to

Records the measured

value. All of the data is recorded in the Standard or Advanced mode.

• When the rotary switch is set to SET-UP

: Serves as the

▼

arrow when browsing in the menus and values.

►

• When the rotary switch is set to

+A (Advanced Mode):

Short Press:

Switches the display through the following three modes:

Display of the impedance recalculated at the selected frequency.

Display of the contact voltage (product Z*I).

Display of R and L.

Long Press:

Enables or disables the audible alarms.

• When the rotary switch is set to SET-UP:

Validation when browsing in the menus and values.

• When the rotary switch is set to MR (Advanced Mode):

Switches the display through the measurement screens and the

measurement date/time.

HOLD

AUTO-HOLD

• When the rotary switch is set to

+A:

Freezes the displayed measurement for as long as the

HOLD

button

is pressed. The NOISE, clamp open (

), and alarm exceedence ( )

icons are visible, if they were active.

• When the rotary switch is set to MR or SET-UP:

Enables or disables the Bluetooth

connection.

• AUTO-HOLD Function:

If the

AUTO-HOLD

mode was enabled during instrument

SET-UP

(see

§ 4.4, menu #11), opening the clamp acts as the identical state to the

HOLD

mode for as long as the clamp is open. The benefit of this function

is that it makes it easy to freeze the measurement with one hand, when

access to the

HOLD

button is difficult.

If the

HOLD

button is not pressed during this time, closing the clamp

automatically exits the

AUTO-HOLD

mode.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for 6417





















































Search results

Summary of Contents for 6417

Reviews:

Related manuals for 6417

Brands by name

Popular brands

AEMC 6417, User Manual

Search results

Summary of Contents for 6417

Reviews:

Related manuals for 6417

Brands by name

Popular brands