AEMC 6417 User Manual Download Page 7

Page: 7 / 52

Clamp-on Ground Resistance Tester Model 6417

5.7 Standard and Advanced Modes..........................................................24
5.8 Memory ...............................................................................................25

5.8.1  Memory Capacity....................................................................25
5.8.2  Storing Measurements into Memory.......................................25
5.8.3  Reading Stored Data ..............................................................25
5.8.4  Erasing the Memory ...............................................................25

5.8.5 Using the ▲ and ▼ Buttons

...................................................26

5.8.6 Exporting Data to a PC ...........................................................26

5.9 Alarm Management.............................................................................26

5.9.1  Voltage Alarm .........................................................................26
5.9.2  Current Alarm .........................................................................27
5.9.3  Impedance Alarm....................................................................27
5.9.4  No Alarm Detection.................................................................27
5.9.5  Priority of the Alarms ..............................................................28

6. MEASUREMENT MODES ..............................................................................29

6.1 Rotary Position

Ω

+A ...........................................................................29

6.1.1  Standard Mode .......................................................................29
6.1.2  Advanced Mode ......................................................................30
6.1.3  General Information ................................................................31

6.2 Rotary Position (A)..............................................................................33

6.2.1 Making a Measurement ..........................................................33

6.3 Rotary Position - (MR) ........................................................................33

6.3.1 Displaying Stored Measurements...........................................33

7. DATAVIEW

SOFTWARE ...............................................................................36

7.1 Installing DataView

............................................................................36

7.2 Ground Clamp Control Panel..............................................................38

8. ANDROID APPLICATION ..............................................................................39

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for 6417





















































Search results

Summary of Contents for 6417

Reviews:

Related manuals for 6417

Brands by name

Popular brands

AEMC 6417, User Manual

Search results

Summary of Contents for 6417

Reviews:

Related manuals for 6417

Brands by name

Popular brands