AdirPro Total Station ATS-120 Series Manual Download Page 15

Page: 15 / 84

2.2.

Functional keys under the basic measuring mode

2.2.1.

Angle Mode (including 2 menu pages)

Page

Soft key

Reference

Function

Save

Record the measured angle in the
selected file.

Set0

Set the horizontal angle as 0°

SetA

Set your desired horizontal angle by
inputting, but the angle should not be
greater than 360°

P1/2

Displays the second page of the soft key
functions

Hold

Locks the horizontal angle readings.

L/R

Switch between HR (horizontal right/
clockwise) and HL (horizontal left/
counter clockwise) mode.

Vertical Angle Mode (altitude angle,
Zenith, Horizontal ‘0’, slope)

P2/2

Displays the first page of the soft key
functions.

Summary of Contents for Total Station ATS-120 Series





















































































Search results

Summary of Contents for Total Station ATS-120 Series

Reviews:

Related manuals for Total Station ATS-120 Series

Brands by name

Popular brands

AdirPro Total Station ATS-120 Series, Manual

Search results

Summary of Contents for Total Station ATS-120 Series

Reviews:

Related manuals for Total Station ATS-120 Series

Brands by name

Popular brands