ADB Safegate RELIANCE AC User Manual Download Page 23 | Manualshive

Page: 23 / 56

background image

6. After installation, make sure that each light fixture functions properly.
7. In order to bond the light fixture to ground, use the supplied screw (Torx M4×6 mm, Torque 2.5Nm) to attach the braided

ground strap to the grounding point on the light fixture. The grounding point is indicated by a grounding symbol and

located on the bottom side.

Remove the fitting from the base

CAUTION

Fall- and trip hazard! When a light fixture has been removed, the base must be fitted with a cover designed for this

purpose or with a spare light fixture.

1. Remove the light fixture from the base using two large flat blade screwdrivers.
2. Disconnect the secondary supply connector.
3. Remove and check the O-ring gasket.

Note

It is recommended to change the gasket, lock nuts or bolts each time the light fixture is removed or dismounted from

the base. For more information, see

INTEROPERABILITY

.

CAUTION

Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product installation and

create multiple safety risks.
Make sure to know what base the light fixture will be installed in, in order to chose the correct gasket, bolts and nuts.
Failure to follow these cautions can result in equipment damage or aircraft FOD. For more information, see

INTEROPERABILITY

4.4 Toe-in

Toe-in of light fixtures can be achieved in two ways:

1. By installing the light fixture in runway/taxiway parallel bases and use light fixtures with built in toe-in.
2. By installing the light fixture in bases installed at an angle relative the runway/taxiway and use light fixtures with no built

in toe-in.

If bases which are installed at an angle are used, provided that they are installed correctly, straight light fixtures, i.e. with no

toe-in, should be used.
The following chapter only regards the case where light fixtures are installed in runway/taxiway parallel bases, i.e. where no

toe-in is achieved by angled bases.

UM-0210, Rev. 2.0, 2020/04/30

13

Copyright

©

ADB Safegate, All Rights Reserved

«
...
21
22
23
24
25
...
»

Summary of Contents for RELIANCE AC

























































Reviews:

No comments

Related manuals for RELIANCE AC

Brand: Oceanled Pages: 28

Brand: DANLERS Pages: 2

Brand: Qazqa Pages: 4

Brand: S.R.Smith Pages: 8

Brand: S.R.Smith Pages: 23

Brand: GE Pages: 2

CLESSY 23.8600.85

Brand: O.N Pages: 9

HI-MAX LAC360064

Brand: Luxonic Pages: 6

Brand: Kartell Pages: 48

Brand: GRNLITE Pages: 14

Brand: Laserworld Pages: 6

home FLP 1100 SOLAR

Brand: Somogyi Elektronic Pages: 15

Brand: Somogyi Elektronic Pages: 20

LED STARCLOTH II

Brand: HQ Power Pages: 35

Brand: MOONRAYS Pages: 4

Brand: Ibiza Pages: 20

Brand: IKEA Pages: 4

Brand: Cooper Lighting Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands