ADB Safegate RELIANCE AC User Manual Download Page 16

Page: 16 / 56

2.1 How to Work with the Manual

•

Familiarize yourself with the structure and content.

•

Carry out the actions completely and in the given sequence.

2.2 Abbreviations and Terms

This document may include the abbreviations and terms listed below.

Abbreviation and term

Description

ASP

Airfield Smart Power

A-SMGCS

Advanced Surface Movement Guidance and Control System

CAA

Civil Aviation Authority

CCR

Constant Current Regulator

FAA

Federal Aviation Administration

ICAO

International Civil Aviation Organization

IEC

International Electrotechnical Committee

ILCMS

Individual Light Control and Monitoring System

LED

Light Emitting Diode

LMS

Light Monitor and Switch unit

NATO

North Atlantic Treaty Organization

NCU

Network Concentrator Unit

SCF

Series Circuit Filter

SCM

Series Circuit Modem

SMGCS

Surface Movement Guidance and Control System

SSU

System Switch Unit

STAC

Service Technique de l'Aviation Civile (France)

STANAG

Standardization Agreement (NATO)

RELIANCE Inset Lights
About this Manual

6
Copyright

Summary of Contents for RELIANCE AC


















































Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands

ADB Safegate RELIANCE AC, User Manual

Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands