ADB Safegate RELIANCE AC User Manual Download Page 17

Page: 17 / 56

3.0 Introduction

RELIANCE - the all in one revolution
The RELIANCE 12

‑

inch range is a bi- or unidirectional low protrusion light-emitting diode (LED) inset light fixture, available in

three versions:

RELIANCE

A LED light fixture with integrated fail open technology with CCR

monitoring compatibility

RELIANCE IQ

A RELIANCE with additional and integrated intelligence (IQ) in a built-in

converter for individual monitoring and control, based on RELIANCE

Intelligent Light Control and Monitor System (ILCMS)

RELIANCE IQ0 RELIANCE IQ light fixture with disabled IQ (ILCMS) functionality. Non-

MON light fixture with possibility to activate IQ at a later stage

Note

RELIANCE IQ light fixtures are not fail-open light fixtures. When IQ is activated the monitoring as well as the control

functionality is handled by the ILCMS system.

3.1 Product Information

Compliance and Standards

Compliance

Description

Application:

RC-

‑

RTN

AS-AC

Reference DS-XXXX:

0167

0174

0175

0176

0186

0187

0188

0209

FAA

AC 150/5345-46 and the FAA

Engineering Brief No. 67

ICAO

Annex 14 Volume 1

EASA

CS-ADR-DSN

Australia

MOS 139

Canada

TP 312

IEC

61827

NATO

STANAG 3316

STAC

PRO/STAC/SE/VIS

Features and Benefits

Efficiency

•

Available in two versions:

•

RELIANCE

™

IQ with integrated intelligence

•

RELIANCE with integrated fail-open (Mon) technology. Fuse resistors are part of the Mon-functionality and spares needs

to be ordered separately.

•

Light Emitting Diode (LED) technology that offers a long-lasting light source with low power consumption

UM-0210, Rev. 2.0, 2020/04/30

Summary of Contents for RELIANCE AC


















































Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands

ADB Safegate RELIANCE AC, User Manual

Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands