ADB Safegate RELIANCE AC User Manual Download Page 54

Page: 54 / 56

D.2.2 ADB SAFEGATE Recycling

ADB SAFEGATE is fully committed to environmentally-conscious manufacturing with strict monitoring of our own processes as

well as supplier components and sub-contractor operations. ADB SAFEGATE offers a recycling program for our products to all

customers worldwide, whether or not the products were sold within the EU.
ADB SAFEGATE products and/or specific electrical and electronic component parts which are fully removed/separated from

any customer equipment and returned will be accepted for our recycling program.
All items returned must be clearly labelled as follows:

•

For ROHS/WEEE Recycling

•

Sender contact information (Name, Business Address, Phone number).

•

Main Unit Serial Number.

ADB SAFEGATE will continue to monitor and update according for any future requirements for EU directives as and when EU

member states implement new regulations and or amendments. It is our aim to maintain our compliance plan and assist our

customers.

RELIANCE Inset Lights
SUPPORT

44
Copyright

Summary of Contents for RELIANCE AC


















































Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands

ADB Safegate RELIANCE AC, User Manual

Search results

Summary of Contents for RELIANCE AC

Reviews:

Related manuals for RELIANCE AC

Brands by name

Popular brands