background image

Page  4

INTRODUCTION

Thank you for buying a spa equipped with a SmarTouch
Digital control systems. Many years of experience went into
the design of this family of controls. You can be assured your
spa control system is the most advanced, it is highly reliable
and will serve you for many years to come.

The control system has been designed with the you the user
in mind. It is very easy to operate and requires a minimal effort
on your part. You may use it just as it comes to you and
without any programming. Yet you have the option of getting
deeply involved in the inner workings of the control if you so
choose. You can custom tailor it to fit your needs.

Please take the time to read at least the first section (next
page) “IN A HURRY - READ THIS” portion of the manual
before starting to use your spa for the first time. You can
familiarize yourself with the rest of the manual at your leisure.
This manual will also serve as a reference if you choose to
modify the operation of your spa.

SAVE THIS MANUAL.

Make it available for other spa users.

You should also have a spa user’s manual which explains
how to care for your spa. Please read and follow all
instructions in your spa user’s manual. Maintaining the proper
levels of pH and the sanitizer will extend the life of your spa
equipment. Improper chemical levels in the spa are sure to
cause premature heater failure as well as failure of other
components in the system

. Failures caused by chemical

imbalance are not covered by warranty.

Summary of Contents for SmarTouch Digital series





























Reviews: