ABB TPS48-H33 Operation Manual Download

Page: 84 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Eliminating malfunctions

Page 54 / 99

HZTL4037_EN

Revision A

August 2016

Charge air pressure too high

Engine performance and engine speed unchanged, suction condition normal

Possible causes

Remedy

Engine

Malfunction in the injection system

Repair or contact manufacturer

Injection mistimed

Set correctly

Engine performance higher than indicated Check engine performance

Turbocharger Manometer display not correct

Replace manometer

Increased speed due to contamination of

nozzle ring

Clean (see chapter Periodic maintenance

work [➙

39]) or contact an ABB Turbo-

charging Service Station

Table 21: Malfunctions during operation – Charge air pressure too high

Reduced compressor performance/efficiency, hence engine performance losses

CAUTION

Compressor damage
A severely contaminated or corroded compressor wheel can reduce the

compressor wheel’s fatigue endurance limit and result in the turbocharger

being damaged.



Rectify malfunction in accordance with the following table.

Possible causes

Remedy

Turbocharger Compressor components severely con-

taminated by the ventilation gases that

have been fed in

Clean (see chapter Periodic maintenance

work [➙

39])

Optimize oil separation

Increased blade vibration, compressor

blade damage due to the ventilation gases

that have been fed in

Correct the feed of ventilation gases ac-

cording to instructions of enginebuilder.

Material of the compressor wheel corrod-

ed due to the feeding in of ventilation gas-

es containing corrosive components

Correct the feed of ventilation gases ac-

cording to instructions of enginebuilder.

Material of the compressor wheel corrod-

ed due to intake air containing exhaust

gases or salt

Prevent exhaust gas leakages in the en-

gine space
Clean (see chapter Periodic maintenance

work [➙

39])

Table 22: Malfunctions during operation – Engine performance losses

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands