ABB TPS48-H33 Operation Manual Download Page 58

Page: 58 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Monitoring operation

Page 28 / 99

HZTL4037_EN

Revision A

August 2016

4.3.5

Replacing the speed sensor

WARNING

Hot speed sensor
Danger of burns. The speed sensor can reach temperatures of more than

100 °C during operation.



Wear safety gloves when disassembling the speed sensor.

Wear safety gloves to protect against thermal hazards.

NOTICE

Sealing of the speed sensor
The speed sensor is designed with a sealing lip and an additional O-ring and

does not need an additional gasket for assembly.

Figure 11: Fitting the speed sensor

Part number

TPS44

TPS48

TPS52

86505

M12 x 1.5

15 Nm

M12 x 1.5

15 Nm

M12 x 1.5

15 Nm

Table 9: Tightening torque (86505)



Reduce the engine performance to idling and then stop the engine. Pay attention to post-

lubrication (

Stopping the engine [➙

37]).



Switch off the lubricating oil supply to the turbocharger.



Disconnect cable connector (86515) from speed sensor (86505).



Unscrew and remove defective speed sensor (86505).



Screw in new speed sensor (86505) as far as it will go and tighten.



Connect cable connector (86515) to speed sensor (86505).



Switch on lubricating oil supply to the turbocharger.

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands