ABB TPS48-H33 Operation Manual Download

Page: 51 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Commissioning

Page 21 / 99

HZTL4037_EN

Revision A

August 2016

Version with water-cooled bearing casing

CAUTION

Failure of bearing casing cooling
Any prolonged failure of the water cooling will shorten the lifetime of the tur-

bocharger.



Make sure that an uninterrupted supply of cooling water is provided during

operation.



Check whether the water pipes are fitted on the bearing casing.

3.2.3

Checks after commissioning (engine in idle mode)

Lubricating system



Keep to the lubricating oil pressure at the inlet.



Keep to the lubricating oil temperature at the inlet.



Refer to chapter

Monitoring operation [➙

23] for admissible values.

Tightness of pipes



Check all the pipes for tightness.

3.2.4

Checks when starting up the engine



Measure speed, oil pressure and charging pressure at various engine performances.



Measure the exhaust gas temperature before and after the turbine.



Measure the air temperature before and after the compressor.



Compare the measured values with the values of the acceptance certificate. Different op-

erating conditions indicate a malfunction (see chapter

Eliminating malfunctions [➙

51]).

NOTICE

Escape of oily fluids
Lubricants and pastes used during assembly can liquefy or vaporise and es-

cape as oily fluids during the initial hours of operation. Continuous escape of

an oily fluid indicates an oil leak.

If there is a leak, contact an ABB Turbocharging Service Station.

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands