ABB TPS48-H33 Operation Manual Download Page 41

Page: 41 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Removing and Installing

Page 11 / 99

HZTL4037_EN

Revision A

August 2016

Removing and Installing

2.1

Turbocharger weight and transportation

Lifting gear with a sufficient load limit must be used for removing and installing the turbo-

charger. The following weight specification applies to the heaviest variant possible. Depending

on the specification, the weight specified on the rating plate may be lower than the standard

value specified here.

Product

Weights [kg]

TPS44

120

TPS48

180

TPS52

250

Table 2: Weight of the turbocharger

One swivel lifting eye (S) is required to safely lift this turbocharger. This is not included in the

ABB Turbo Systems scope of delivery.

Swivel lifting eye (S) to be used

Product

Thread

Length
L [mm]

Minimum load

limit [kg]

TPS44

125

TPS48

190

TPS52

M10

260

Table 3: Swivel lifting eye (S) to be used

Figure 4: Turbocharger transport

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands