ABB TPS48-H33 Operation Manual Download

Page: 72 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Periodic maintenance work

Page 42 / 99

HZTL4037_EN

Revision A

August 2016

Cleaning the absorption segments

(see Figure

)



Loosen the tension bands (81270).



Remove the cover grid (81266).



Pull out and bend up the sheet-metal coverings (81137), and remove the absorption seg-

ments (81136).



Clean the absorption segments (81136).

When cleaning, note that the absorption segments (81136) must only be cleaned lightly

with compressed air, a soft brush or a moist cleaning cloth.



Have any heavily contaminated absorption segments replaced by an ABB Turbocharging

Service Station.

Fitting the filter silencer

(see Figure

)



Insert the absorption segments (81136) into the sheet-metal coverings (81137).



Bend the sheet-metal coverings (81137) back to their original shape and insert into the

slotted guides in the filter silencer body (81135).



Fit the cover grid (81266).



Fit the tension bands (81270) and tighten them at the locks (81271).



Any tension bands that have become damaged must be replaced.



Fit the filter ring (81265), if present.

Summary of Contents for TPS48-H33



































































































































Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands

ABB TPS48-H33, Operation Manual

Search results

Summary of Contents for TPS48-H33

Reviews:

Related manuals for TPS48-H33

Brands by name

Popular brands